- AUDI RADIO CODE WITH VAG COM HOW TO
- AUDI RADIO CODE WITH VAG COM INSTALL
- AUDI RADIO CODE WITH VAG COM FULL
- AUDI RADIO CODE WITH VAG COM PLUS
- AUDI RADIO CODE WITH VAG COM TV
There are whole host of settings you can access here, like adjusting MMI timings, visible options - apparently you can even adjust the TV blackout speed or remove it. Apparently you can access this hidden menu by holding down CAR and SETUP for five/six seconds. (This may require the "real" MMI 2G, it may not work on a Concert/Symphony radio and MMI 3G hidden menu is enabled differently, see below. I've tried the coding and indeed it works! The tilting is not that much though, but can be usable to prevent curb-rash The coding is: Module 52: Door Elect, Pass.: Byte 4 Value 40, change to 4C (non-folding mirrors mounted) Value 50, change to 5C (folding mirrors mounted)Īll that said, here are some of the interesting tweaks you can make with VAG-COM: Hidden menu: C99 reported () in an thread how you can access a hidden maintenance menu via MMI. Someone at the German motor-talk forum found a coding to activate the "passenger mirror tilt when reversing" option, even if you don't have the memory seats, which usually are mandatory for this feature.
Coding - 07 - Long Coding Helper - Byte 4 Bit 0 - Change 0 to 1 -Activate Däcktryckskontroll non-nav 56 - Radio Coding - 07 - Long Coding Helper - Byte 8 Bit 6 0 to 1 03 - ABS Brakes Security Access - 16 (code 61378) Coding - 07 - Long Coding Helper - Set Byte 1 Bit 3 from 0 to 1 Or "check" Tire Pressure Monitoring (PR-7K6) 17 - Instruments Coding - 07 - Long Coding Helper - Byte 4 Bit 0 - Change 0 - 1 Or Select Tire Pressure Monitoring (TPMS) installed. Coding - 07 - Long Coding Helper - Byte 16 Bit 6 - Set this bit manually to “1” - (1 = active) -release brake without seat belt Module - 53 Adaptation - channel 7 - 1 to 0 -Fog Light turns on with turn signal (Curb Side Lighting)** 09 – Cent.
Security Access - 16 Adaptation - 10 - Channel 19 - change 1 to 0 -DIS with Efficiency Program for MY2010+ (Not a complete Program without the Start/Stop System): 17 - Instruments Adaptation - 10 - Channel 77 - change 0 to 255 -Enabling/disabling doors locked/alarm armed sound 46 - Central convenient Coding - long coding - Byte 1 bit 2 Unlocking beep 46 - Central convenient Adaptation - Channel 63 - add 4 to previous value -Īmbience lightning 56 - Radio Coding - 07 - Long Coding Helper - Byte 8 Bit 7 - Interior Light Settings active - (1 = active) 09 – Cent.
AUDI RADIO CODE WITH VAG COM FULL
STG Coding - Long Coding Helper - Byte 3 Bit 2 - LEDs remain at full brightness with parking lights (1 = active) Bit 7 - Turn off LED-strip DRLs with indicators (1 = active) -Needle Sweep STG 17 - Instruments STG Coding - Long Coding Helper - Byte 1 Bit 0 – Gauge Test/Needle Sweep (1 = active) Bit 3 – LAP-Timer (1 = active) -Disable automatic rear window wipe on the Avant 09 – Cent.
AUDI RADIO CODE WITH VAG COM PLUS
Happy to say that following some research Callum returned a few days later and I was able to remove ADS from the unit, as retrofitting is not possible, and then fully re-parameterise the firmware in order to remove the AMI configurations and add AUX Input functionality.īelow is a post from the VAG Car Coding blog:Īudi A1 8X 1.2TFSI RMC Nav Plus Retrofit and Coding!
AUDI RADIO CODE WITH VAG COM HOW TO
The only issue I had on the day was that the new unit had been removed from a vehicle which had Audi Drive Select and an AMI port and at the time I was not sure how to remove the ADS and recode said unit for the AUX input which was in the car from the factory.
AUDI RADIO CODE WITH VAG COM INSTALL
Happy to say that VAG Car Coding was able to install the new RMC NAV Plus unit, remove the component protection and then fully re-code the unit in order to work with the cars existing Bose system. Thought I would post up on this as Callum contacted me in order to sort out this retrofit
0 kommentar(er)
